Username:     
Password:     
             

Forum

# 1   2009-07-11 21:41:02 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Error 103: Target power failure: Measured 1.100000V

Hi. I just got my Primer2, and I get the above message when trying to run Circle_Mgr
The device is fully charged (green light's on), and everything seems to run fine on it (the games, etc). But I can't communicate with it from my PC! (Plain old Windows XP).

Also, if I unplug it from the USB port, and then immediately plug it back in, the green light goes out, and the red one comes on. And it takes a few minutes to get the green light back on. That doesn't seem to make sense for being unplugged for just a few seconds.

I see this error has come up for some other people too. What's going on? The device is unusable for development, of course.

(Sorry if this appears twice - I thought I'd already posted it).

Thanks,
Steve

Offline

 

# 2   2009-07-13 08:20:12 Error 103: Target power failure: Measured 1.100000V

Francis
Administrator
From: France-Grenoble
Registered: 2007-07-09
Posts: 890

Re: Error 103: Target power failure: Measured 1.100000V

Quite strange. This error means that RLink detects a wong voltage for the STM32. On the other hand, if the game work properly, the STM32 voltage is correct... (it couldn't work at 1.1V).

The behaviour of the LEDs (charger status) is correct. When you plug/unplug, the charger starts a charging sequence.

The voltage is measured on a two resistor bridge. It could be that one of these resistors is wrong, but the STM32 FLASH had been loaded - and tested- at the factory...

Try to update RIDE+KitARK.. If it does not work, we'll see how to replace it.

Offline

 

# 3   2009-07-14 02:51:27 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Re: Error 103: Target power failure: Measured 1.100000V

Thanks. I'll do that. I assume you mean to download the latest Ride version. But I don't know what KitArk is (I just got this thing so I'm not up to sped). What is it?

Offline

 

# 4   2009-07-15 14:42:42 Error 103: Target power failure: Measured 1.100000V

matloub
Member
Registered: 2008-02-21
Posts: 98

Re: Error 103: Target power failure: Measured 1.100000V

Hi

You need to uninstall RKitARM and after Ride7.
Then install Ride7 and RKit-ARM downloaded from http://www.mcu-raisonance.com/mcu_downloads.html

Regards,
Matloub

Offline

 

# 5   2009-07-22 04:15:45 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Re: Error 103: Target power failure: Measured 1.100000V

I've tried to download that, but it requires you to log in, and it keeps saying "Logon refused". I asked for a new password (though the old one used to work), and it says it sent it, but no email showed up. So then I also re-registered with another email address, and it sais it sent an email there, but still nothing. Is anybody home at Raisonance? I got a second unit, which doesn't seem to have the battery problem), but I still get the same 103 error when trying to run Circle.Mgr.

I'd reeeeeally like to try this device out, but it's getting frustrating with the lack of support. Okay, I'm done whining now... smile

Offline

 

# 6   2009-07-22 05:43:18 Error 103: Target power failure: Measured 1.100000V

ShadowPhoenix
Member
Registered: 2009-02-11
Posts: 57

Re: Error 103: Target power failure: Measured 1.100000V

www.bugmenot.com

This site is where people submit logins/passwords to site they don't need/use.  it's a really nice feature when sites make you register for no reason. (except to spam your email?)

Now, your problem IS because of outdated Ride7. I had exact same problem. Make sure to update ride7 + armkit for it and then connect debug USB port and keep primer2 on.

Offline

 

# 7   2009-07-22 15:09:33 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Re: Error 103: Target power failure: Measured 1.100000V

ShadowPhoenix:

Thanks. That's a GREAT idea (having those logons available). Unfortunately, I get "Logon Refused" for the three that were on the site. Maybe Raisonance is just down for a while? The site seems to function otherwise.

That's also good to know that you had the same error, and the the latest Ride fixed it. Now, if I could just GET a copy!

Steve

Offline

 

# 8   2009-07-22 19:48:42 Error 103: Target power failure: Measured 1.100000V

ShadowPhoenix
Member
Registered: 2009-02-11
Posts: 57

Re: Error 103: Target power failure: Measured 1.100000V

saustin98 wrote:

ShadowPhoenix:

Thanks. That's a GREAT idea (having those logons available). Unfortunately, I get "Logon Refused" for the three that were on the site. Maybe Raisonance is just down for a while? The site seems to function otherwise.

That's also good to know that you had the same error, and the the latest Ride fixed it. Now, if I could just GET a copy!

Steve

Three on the site? Are you sure you are using the same site?

http://www.bugmenot.com/view/mcu-raisonance.com

Make sure to look for mcu-raisonance and not just raisonance wink

Try now, I think that should solve it.

Offline

 

# 9   2009-07-22 20:20:26 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Re: Error 103: Target power failure: Measured 1.100000V

Right. I just clicked your original link. Now, when I click this one, there's only one logon id,
(praveen2k10@yahoo.com).

Still, it's a great idea, and I'll definitely look there for future cases where I reeeeeally don't want to have to register for something.

Offline

 

# 10   2009-07-22 21:02:12 Error 103: Target power failure: Measured 1.100000V

ShadowPhoenix
Member
Registered: 2009-02-11
Posts: 57

Re: Error 103: Target power failure: Measured 1.100000V

saustin98 wrote:

Right. I just clicked your original link. Now, when I click this one, there's only one logon id,
(praveen2k10@yahoo.com).

Still, it's a great idea, and I'll definitely look there for future cases where I reeeeeally don't want to have to register for something.

I think you tried the wrong site, mcu-raisonance vs just raisonance smile.

In any way, this log in should work. Did you get your primers to wrok now?

Offline

 

# 11   2009-07-22 22:24:04 Error 103: Target power failure: Measured 1.100000V

saustin98
New member
Registered: 2009-06-01
Posts: 6

Re: Error 103: Target power failure: Measured 1.100000V

Sigh... no. As recommended, I de-installed Ride and RKit, downloaded the new ones, reinstalled them, and got the same error (with a new copyright line in the output text, so I know I'm running the new code).

So I think I've had enough. I've asked for a refund from the vendor (Future Electronics). Let's hope that goes well.

Offline

 

# 12   2009-07-23 00:42:01 Error 103: Target power failure: Measured 1.100000V

ShadowPhoenix
Member
Registered: 2009-02-11
Posts: 57

Re: Error 103: Target power failure: Measured 1.100000V

Did you make sure Pirmer2 is on when you plug the cable in smile?

Offline

 

# 13   2009-07-23 01:18:10 Error 103: Target power failure: Measured 1.100000V

wbaklanoff
New member
From: Las Vegas, NV
Registered: 2009-04-06
Posts: 1

Re: Error 103: Target power failure: Measured 1.100000V

Interesting note: The link given for updated s/w downloads by matloub "http://www.mcu-raisonance.com/mcu_downloads.html" is being redirected to "http://www.raisonance.com/; then the New Ride 7... More info link is being redirected back to "http://raisonance.com/"

Offline

 

# 14   2009-07-23 14:28:40 Error 103: Target power failure: Measured 1.100000V

matloub
Member
Registered: 2008-02-21
Posts: 98

Re: Error 103: Target power failure: Measured 1.100000V

Hi

@wbaklanoff thanks for letting us know this point
The link was broken during maintenance operation.
It has been fixed now.

Offline

 

# 15   2010-06-08 07:50:20 Error 103: Target power failure: Measured 1.100000V

tvamos73
New member
Registered: 2010-04-04
Posts: 1

Re: Error 103: Target power failure: Measured 1.100000V

Hi,
I was fighting with my Primer2 and... so interesting...
I cannot download any software. The failure: Error 103: Target power failure.
After 2 days I find that:
    - I have to push the button if this problem is realized.
BR / Tamás

Offline

 

# 16   2014-08-29 01:13:45 Error 103: Target power failure: Measured 1.100000V

snjunior
New member
Registered: 2014-08-29
Posts: 1

Re: Error 103: Target power failure: Measured 1.100000V

I have found the same problem using RLink with JTAG/SWD adapter and STM32F4-Discovery board. In my case the error message said : Target Power Failure : Measured 4.90000V.

Does  anyone know the pinout for this adapter ( JTAG option ) or some clue about it  ( Target Power Failure Error) ?

Thanks

Last edited by snjunior (2014-08-29 01:15:56)

Offline

 

# 17   2014-08-29 09:21:24 Error 103: Target power failure: Measured 1.100000V

Etienne.C
Administrator
Registered: 2012-12-04
Posts: 71

Re: Error 103: Target power failure: Measured 1.100000V

Hello,
Please, have a look of our Raisonance Forum at http://forum.raisonance.com/viewtopic.php?id=2449.

You probably connected the wrong pin to the Discovery board.
Ride 7.50.14.0185 and RKit-ARM 1.54.14.0185 are supporting the STLink v.2 then you can install these new versions (http://support-raisonance.com/extranet/ … ool__id__7).

Rlink is supporting more MCUs than the STLink but in your case you can connect the STLink to the Discovery board (don't need custom connection) instead of the Rlink.

Best regards,

Offline

 

Board footer