STM CircleOS forum / how to use the code

prajwal · 2010-02-27 07:49:10

how to use this application on stm32 primer2?

ntrf.zns · 2010-02-27 08:35:14

First you need to install software (Ride IDE and ARM Toolkit). If you want to intall MP3Player to the Primer2, go to the Lib_XXX_add_to_circle subfolder and launch the add_to_circle.bat file. Make sure you connected (using Debug port - you will see red ligt near joystick) and turned on your device.

Last edited by ntrf.zns (2010-02-27 08:36:06)

ankita madan · 2010-07-05 11:55:22

Hello,

After connecting a USB cable to DEBUG, I see the LED near the joystick glow for a second and then it turns off. Now, I switch the Primer ON. And I launch the BAT file as suggested as below. It shows the following:

Connecting to RLink... OK
Connecing to target...
Error 303 : Unable to read Id code..."

any suggestion?

Rgds,
Ankita

yrt · 2010-07-06 08:50:57

The Led behavior is normal at USB connection (it indicates the busy state of the embedded RLink). Did you try to restore the factory firmware, or debuging under Ride environment ?

ccf · 2010-09-15 12:18:09

I wanted to test the MP3_Player_1.01 application.
So I did install CircleOS 3.82 on my Primer2.
Than I did add the MP3_Player to it (with add_CircleOS_application.bat).

Everything works fine, I can start the MP3_Player, browse through the SDcard, chose an MP3 or an WAV file. But when I start playing, no audio output occurs, neither on the headphone nor on the speaker. I did increase volume and enable/disable the headphone but nothing could be heared. The flying text is scrolling so I think the MP3 is playing, but whats the problem with the audio output ?
Any suggestions ?

Thanks

PS: I did additional install PlayWav1.1 and there the audio output works, so the MP3_Player_1.01 seems not to be functional. However it is not a hardware problem.

Last edited by ccf (2010-09-15 12:29:11)

repzak · 2010-09-16 05:22:54

Hello,

Did you use the application for library 3.10??

Can you try downgrade to circel_os 3.80 or use the unoffical embedded 3.72?

Kasper

ccf · 2010-09-16 14:47:06

>> Did you use the application for library 3.10??

Yes, I did use the application for library 3.10 from path:
MP3_Player\LIB_3.10_add_to_Circle\MP3_Player_Lib.lib

>> Can you try downgrade to circel_os 3.80 or use the unoffical embedded 3.72?

The only circel_os other than 3.82 I did found on http://www.stm32circle.com/projects was a circle_os 3.7.
After I installed this, it went out to be a circle_os 3.71.
However I did add PlayWav and MP3_Player.
PlayWav works while MP3_Player crashes immediately after having selected a MP3 file to be played. So no flying text occur and my primer finally hung up until I disconnected the battery via JP3.

repzak · 2010-09-17 11:31:18

Hello,

In the MP3 zip file there is a 3.72 (non offical)

It must work with that... else try another SD card or some other MP3 songs...

Kasper

yrt · 2010-09-20 07:09:46

Hi,

I confirm that the 3.1 version of MP3 player is running with latest CircleOS versions.

Yves

repzak · 2010-09-20 07:49:24

Thank you

Kasper

# 1 2010-02-27 07:49:10 how to use the code (project: MP3 Player 1.01)

how to use the code (project: MP3 Player 1.01)

# 2 2010-02-27 08:35:14 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 3 2010-07-05 11:55:22 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 4 2010-07-06 08:50:57 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 5 2010-09-15 12:18:09 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 6 2010-09-16 05:22:54 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 7 2010-09-16 14:47:06 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 8 2010-09-17 11:31:18 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 9 2010-09-20 07:09:46 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

# 10 2010-09-20 07:49:24 how to use the code (project: MP3 Player 1.01)

Re: how to use the code (project: MP3 Player 1.01)

Board footer